Upperby Yard

You are here: Home > Forum > Simulations > Released > Carlisle > Upperby Yard

Page 1 of 1

Upperby Yard 19/11/2012 at 11:01 #37702
hotwellian
Avatar
211 posts 		Hi,

Running: Carlisle 15-10-2009 v1-61 (0445).WTT

Probably me being stupid, but I cannot figure how to get 6J08 into Upperby Yard. I read the wiki manual on this point but it just says:

There is a long standing interlocking fault with the real signalling where signal CE285 incorrectly reverts to danger when points 706A/B are swinging from normal to reverse. Therefore any routes from signal CE285 should be cancelled before swinging the points before setting a route from signal CE287 to CE267.

This doesn't help me, especially as I can't find any signals with those numbers. Any ideas?
Log in to reply
Upperby Yard 19/11/2012 at 11:20 #37704
AndyG
Avatar
1835 posts 		I wonder whether as 6J08 is an Engineer's train (tamper), it actually goes to the engineer's siding rather than the yard proper.
May be a TIPLOC discrepancy in the original data.
I can only help one person a day. Today's not your day. Tomorrow doesn't look too good either.
Log in to reply
The following user said thank you: hotwellian
Upperby Yard 19/11/2012 at 12:27 #37714
hotwellian
Avatar
211 posts 		Mmmm,

That is an idea
Log in to reply
Upperby Yard 19/11/2012 at 14:50 #37721
jc92
Avatar
3631 posts 		" said:
I wonder whether as 6J08 is an Engineer's train (tamper), it actually goes to the engineer's siding rather than the yard proper.
May be a TIPLOC discrepancy in the original data.
I would say so, upperby yard is largely OOU, potentially tho might share a TIPLOC
"We don't stop camborne wednesdays"
Log in to reply
Upperby Yard 27/11/2012 at 13:01 #38195
Javelin395
Avatar
270 posts 		Just discovered this thread having encountered the issue with 6J08. According to Phil Deaves Railway Codes website Upperby Engineers Siding and Upperby Yard do not share TIPLOC codes.

Carlisle Upperby Civil Engineer's Sidings = CARLUES

Carlisle Upperby English Welsh & Scottish Railway = CARLAPC

Carlisle Upperby Maintenance Depot = CARLUMD

Carlisle Upperby Traction Maintenance Depot = CARLTMD

Hope this is of interest.
Log in to reply
Upperby Yard 02/12/2012 at 15:03 #38410
Adrian the Rock
Avatar
111 posts 		One thing that puzzles me about this: the sim's TT validation reports that routing a train from Upperby Bridge Jn directly to Upperby Yard is valid. From the track layout, the only way of doing this would be to use the facing crossover immediately in advance of CE264, but that's not controlled from the panel and there is no GF visible (in 2000s mode) for operating it.
Log in to reply
Upperby Yard 02/12/2012 at 15:23 #38411
postal
Avatar
5191 posts
Online 		" said:
One thing that puzzles me about this: the sim's TT validation reports that routing a train from Upperby Bridge Jn directly to Upperby Yard is valid. From the track layout, the only way of doing this would be to use the facing crossover immediately in advance of CE264, but that's not controlled from the panel and there is no GF visible (in 2000s mode) for operating it.
Thanks. It was put on the Bug Board last month as "Impossible route being validated by TT ".
“In life, there is always someone out there, who won’t like you, for whatever reason, don’t let the insecurities in their lives affect yours.” – Rashida Rowe
Log in to reply
The following user said thank you: Adrian the Rock
Upperby Yard 02/12/2012 at 19:02 #38413
TomOF
Avatar
452 posts 		I can't stop it from validating without breaking other things, but as you say you should at least get a warning.

It's been a known issue for some time but it was low priority.

Thanks
Log in to reply
Back